Quick Answer: Can You’Re Gelcoat A Fiberglass Pool?

Can I paint a fiberglass pool?

One of the things you can do to maintain a fiberglass swimming pool is to paint it.

You can hire a company that specializes in painting fiberglass swimming pools but that can cost a small fortune.

You can purchase all of the needed supplies at most local marine supply stores and home improvement stores..

Is a fiberglass pool worth the money?

Fiberglass and concrete tend to cost about the same initially. … That said, in terms of total cost of ownership, it’s worth noting that maintaining a fiberglass pool is generally cheaper. That’s because fiberglass is more algae resistant, and therefore could save you money on chemicals over the life of the pool.

How do you gelcoat a fiberglass pool?

PreparationTape off areas in the fiberglass pool that will not receive gel coat with 2-inch painter’s tape. … Check the gel-coat surface of the pool for cracks. … Sand the entire gel coat surface with 150-grit sandpaper. … Wipe the sanded area down with acetone.More items…

Can you recoat a fiberglass pool?

How do you redo the gelcoat on your fiberglass pool? The short answer: you don’t. Gelcoat is applied in a controlled manufacturing plant for several key reasons: It takes a long time to dry and cure.

What are the disadvantages of a fiberglass pool?

Cons of a Fiberglass PoolLimited shapes and swimming pool designs.No wider than 16’Repairs on some colored finishes do not match.Higher initial cost.

What is the best kind of paint to use on fiberglass?

acrylic latex paintThe Sunrise Window company recommends an acrylic latex paint for fiberglass. Acrylic paint adheres well to fiberglass, overcoming one of the main challenges to painting this material. Acrylic paint is less likely to crack and blister, and will hold up well to cleaning.

Can you use enamel paint on fiberglass?

Enamel paints can be applied to virtually any surface — wood, fiberglass or metal — provided that proper preparation is carried out. … So give careful consideration to where this paint is used, because chances are high you’ll be reapplying it every few years.

How do you fix fiberglass pool blisters?

The repair procedure is to drain the pool, sandblast the interior, grind out the blisters and add putty to the affected area. A new mat of fiberglass is applied, and a vinylester resin reseals that mat before a new gel coat is put on.

How do you maintain a fiberglass pool?

Basic maintenance for a fiberglass pool:Clean regularly, with products made specifically for fiberglass pools.Check water chemistry.Run the pool filter.Keep water level above the skimmer.

Can fiberglass pools be heated?

Heat. Fiberglass pools heat up quicker and retain heat longer than concrete pools. The fiberglass shell and liner 8 are thinner and made of a material that does not absorb heat, meaning that your water will warm faster and stay warm longer. … This process takes much longer and requires more energy to warm the water.

How long will a fiberglass pool last?

25 yearsA fiberglass pool is expected to last up to more than 25 years – the reason they are the most low-cost option in the long run. Their surface does not support algae growth and resists stain, which means maintenance cost and hassle is significantly minimized.

What is the best paint for a fiberglass pool?

Epoxy pool paintEpoxy pool paint is the only suitable material to paint a fiberglass pool. Buy enough to paint two coats for a long lasting finish. Measure your pool carefully to add up all the surface area of the floor, walls and steps, then buy more than enough Epoxy pool paint to cover the surface, twice.

Do fiberglass pools crack?

Fiberglass pools can craze, or check crack from imprecise manufacturing, or when the surface is not fully supported, like under the steps, or areas where the backfill is eroded. Gel coat can also crack during transport and installation, if it gets bumped around too much.

How deep can fiberglass pools be?

Most fiberglass pools tend to be 3 ½’ to 5 ½’ deep on pools that are 27′ long and smaller. On pools that are 27′ to 35′ long the depths range from 3 ½’ to 6 ½’. On pools that are 35′ to 44′ long the depths can go anywhere from 3 ½’ to 8 ½’ deep.

Is it safe to empty a Fibreglass pool?

A fibreglass pool is the most dangerous to drain and should only be done by a professional. Older pools may not have been built structurally to hold back the weight of the dirt against it when the pool is drained. This can cause the walls to collapse. … A fibreglass pool must be braced if emptied.

Can fiberglass pools be salt water?

Fiberglass swimming pools are very compatible with salt water systems. … Salt water is abrasive on the interior surfaces of concrete/ gunite pools, especially those that have plaster within them. Many families report that they enjoy swimming within a pool that has a salt water system.

When should I resurface my fiberglass pool?

In the case of fiberglass pool resurfacing, the common wisdom is they should last 25 years if you apply 2 coats for the best fiberglass pool resurfacing.

How much does it cost to ship a fiberglass pool?

If you have your pool built and shipped directly to you based on your color and accessories, expect to pay (on average) $1,500 – $3,500 depending on how far you live from a manufacturing plant. The cost per mile is generally broken down based on widths.

Can I install a fiberglass pool yourself?

If you’re just starting your research, you’re probably thinking: “Fiberglass pools are conceptually easy to install. … However, fiberglass pools are a perfect Do-It-Yourself project for anyone with basic excavation and plumbing experience—and, of course, time.